In This Guide
- Why Safety Guards Matter
- Safety Guards for Circular Saws
- Safety Guards for Table Saws
- Safety Guards for Bandsaws
- General Power Saw Safety Rules
- Personal Protective Equipment for Power Saw Use
- Comparing Radial Arm Saw Motors and Sizes
- Radial Arm Saws to Pair with Good Guarding
- Frequently Asked Questions
- Conclusion
Featured Radial Arm Saw

OMGA Inc
OMGA RN 700 14" Radial Arm Saw
$8,157.00
Reliable 5 HP motor and an advanced carriage guidance system power this 14 inch saw for accurate cross cutting, ripping, beveling and angle cutting. Whatever the blade size, confirm the guarding is in place before the first cut.

OMGA Inc
OMGA RAS 900 18" Radial Arm Saw
$15,591.00
Power comes from a 7.5 HP motor, with a heavy-duty cast iron arm, on this 18 inch saw for professional cross cutting, ripping, beveling and angle cutting. It is a large industrial machine, so plan operator training and guard checks around it.

Castaly
Castaly Automatic Cutting 14" Radial Arm Saw RS-640-AO
$23,089.00
Motorized cutting cycle for automated crosscut production, with a 4.5 HP 3-phase motor on a 14 inch saw. The powered cycle reduces manual labor, so read how its guarding is arranged before relying on it.

Maggi USA
Maggi Big 800CE Radial Arm Saw MAG-BIG800CE
From $6,550.00
Extended cutting capacity on a heavy cast build with an eight-bearing carriage system, aimed at professional woodworking operations. For a machine this large, check guard coverage and arm travel before you buy.
Why Safety Guards Matter
A safety guard is the primary engineered barrier between an operator and a moving saw blade. OSHA and ANSI standards require power saws to be equipped with guards that cover the cutting blade to the depth of the teeth — both above and below the base plate or shoe on circular saws, and at the blade exposure point on table saws and bandsaws.
Guards serve four core functions: they prevent accidental contact with the blade, they contain debris ejected during cutting, they help ensure operators use the tool as designed, and they provide a visual indicator of the blade's location. Removing or bypassing a guard doesn't just violate safety regulations — it removes the only mechanical barrier between the operator and a blade spinning at thousands of RPM.
OSHA requirement: Power saws must be equipped with guards both above and below the base plate or shoe. The upper guard must cover the saw to the depth of the teeth. The lower guard must cover the saw to the depth of the teeth and automatically retract when the blade contacts the workpiece. Failure to maintain functioning guards is an OSHA violation and a leading cause of power saw injuries.
Safety Guards for Circular Saws
Circular saws are required to have two guards: an upper blade guard and a lower blade guard.
| Guard | Function | OSHA Requirement |
|---|---|---|
| Upper Guard | Fixed cover over the top portion of the blade | Must cover blade to full depth of the teeth; exception for bevel cuts |
| Lower Guard | Spring-loaded cover that retracts when blade contacts workpiece | Must cover blade to depth of teeth; must auto-retract when cutting, auto-return when blade lifts |
The lower guard is a spring-loaded shield that automatically retracts as the saw contacts the workpiece and snaps back over the blade the moment the saw is lifted away. It must retract and return smoothly on every cut. If the spring is weak, the guard sticks, or the guard doesn't fully cover the blade when at rest, the saw should be taken out of service until repaired.
Key circular saw safety practices:
- Read the owner's manual before use and follow all manufacturer safety guidelines
- Check that the saw is properly grounded and all components are tight before starting
- Never bypass, remove, or tie back the lower guard for any reason
- Avoid using a circular saw in wet conditions or poorly lit areas
- Use a push stick or guide when feeding material near the blade — keep fingers away
- Never force the saw — let the blade speed and tooth geometry do the cutting
- Unplug the saw (or remove the battery) before inspecting, adjusting, or changing the blade
- Never leave a running saw unattended
Safety Guards for Table Saws
Table saws have a more complex guard system than circular saws because the blade is stationary and the workpiece moves through it. The three primary safety components are:
Blade Guard
A housing that covers the blade above the table surface. Must be in place for all ripping and cross-cutting operations where the guard doesn't interfere with the cut.
Riving Knife / Splitter
A blade-shaped plate that sits directly behind the saw blade in the kerf, preventing the workpiece from closing on the blade and causing kickback — the most dangerous table saw event.
Anti-Kickback Pawls
Spring-loaded toothed fingers that allow material to pass forward but dig into it if it starts to travel backwards toward the operator — preventing ejection.
Key table saw safety practices:
- Ensure both the saw and the motor frame are properly grounded
- Keep your body out of the direct line of the blade — stand to the side of the cut path
- Use a brush (not your hand) to clear scrap from the table while the blade is running
- Shut off power and wait for the blade to fully stop before adjusting the guard or fence
- Lock the power off and unplug before changing blades
- For long stock, get a helper or use a roller stand — never reach across the blade to support material
- Keep the area around the saw clear of loose material to prevent tripping
- Wear fitted clothing; avoid loose sleeves, ties, or jewelry near the blade
Safety Guards for Bandsaws
A bandsaw uses a continuous looped blade that runs between two wheels. The guard consists of an adjustable blade guide and housing that covers all blade surfaces except the portion exposed between the upper guide and the table surface. The guard height must be adjusted for each workpiece — it should be set as close to the workpiece as practical, with no more than 1/4 inch of clearance above the top surface of the material being cut.
Key bandsaw safety practices:
- Always wear approved safety glasses or a face shield during operation
- Remove loose clothing, roll up sleeves, and remove any dangling jewelry before starting
- Use non-slip footwear and anti-skid floor mats around the saw
- Use ear protection during extended operation
- Work in a well-ventilated area; use dust masks when cutting materials that produce fine particles
- Ensure the bandsaw is mounted securely on a stable, level surface
- Do not wear gloves or hold the workpiece with a rag — either can get caught in the blade
- Keep hands positioned safely away from the blade path at all times
- Never leave a running bandsaw unattended
General Power Saw Safety Rules
These rules apply across all types of power saws regardless of blade type or motor configuration:
Personal Protective Equipment for Power Saw Use
| PPE Item | Why It's Required | Applies To |
|---|---|---|
| Safety glasses / face shield | Flying chips, sawdust, and blade debris travel at high speed toward the operator | All power saws |
| Hearing protection | Sustained exposure to saw noise above 85 dB causes permanent hearing damage | All power saws; required in commercial settings |
| Dust mask / respirator | Wood dust is a known respiratory hazard; masonry cutting releases crystalline silica | All cutting; N95 or better for masonry |
| Steel-toed boots | Dropped saws and heavy workpieces cause foot injuries | All power saw use on job sites |
| Heavy work gloves | Blade handling during changes; carrying cut material with sharp edges | Blade changes and material handling only — not while operating the saw |
| Fitted clothing | Loose sleeves, ties, and jewelry catch in moving parts and pull hands into the blade | All power saw use |
Note on gloves: Work gloves should be worn when handling blades or carrying cut material — but not while operating most saws. A glove that catches in a blade can pull a hand in faster than a bare hand would be released. Follow the specific manufacturer guidance for each tool.
Comparing Radial Arm Saw Motors and Sizes
The radial arm saws from our store that the guide pairs with good guarding are lined up here. Motor size in the Key feature column is the place to start, then plan the guarding around the machine you pick.
| Model | Price | Key feature | Best for |
|---|---|---|---|
| Castaly 12" Radial Arm Saw RS-612 | $4,389.00 | 2 HP single-phase motor, laser guide, compact design | Small to mid-sized shops doing crosscuts and bevels |
| OMGA RN 450 12" Radial Arm Saw | $7,789.00 | 4 HP motor for cross cutting, ripping, beveling and angle cuts | Professional shops that need ripping as well as crosscuts |
| Maggi Junior 640CE Radial Arm Saw MAG-JUNIOR640 | From $5,850.00 | Heavy cast components with an eight-bearing carriage | Accuracy and long-term durability in a pro shop |
| Castaly 16" Radial Arm Saw RS-660 | $6,259.00 | 4.5 HP 3-phase motor with precision arm travel | Cabinet makers and production facilities |
Match the motor size and shop type in the table to your work, then confirm the guard setup for that saw before you cut.
Radial Arm Saws to Pair with Good Guarding
Radial arm saws are stationary machines where guarding matters on every cut. Before buying any model below, check how its blade guard works and compare motor size with your jobs.
1. Castaly 12" Radial Arm Saw RS-612 — $4,389.00
Laser guidance and a 2 HP single-phase motor suit crosscuts, bevels and angle cuts in small to mid-sized woodworking shops. View more >
2. OMGA RN 450 12" Radial Arm Saw — $7,789.00
Runs a dependable 4 HP motor for cross cutting, ripping, beveling and angle cutting in a compact 12 inch industrial frame. View more >
3. Maggi Junior 640CE Radial Arm Saw MAG-JUNIOR640 — From $5,850.00
An eight-bearing carriage system and heavy cast components make this a pick for professional shops that need accuracy and long-term durability. View more >
4. Castaly 16" Radial Arm Saw RS-660 — $6,259.00
Industrial crosscutting power from a 4.5 HP 3-phase motor and hardened precision-ground rails, for cabinet makers and production facilities. View more >
Frequently Asked Questions
What is the proper safety guard for a power saw?
All power saws must be equipped with guards above and below the base plate or shoe that cover the blade to the full depth of the teeth. On circular saws, the upper guard is fixed and the lower guard automatically retracts when the blade contacts the workpiece and returns when lifted. On table saws, the guard system includes a blade housing, a riving knife or splitter, and anti-kickback pawls. On bandsaws, an adjustable guide housing covers all blade surfaces except the cutting zone between the upper guide and the table.
Is it legal to remove the safety guard from a circular saw?
No. OSHA regulations require safety guards to be in place and functioning during all powered saw operations. Removing or bypassing a guard is an OSHA violation and constitutes willful negligence in the event of an injury. Some specific operations (such as plunge cuts or certain dado cuts) require the guard to be adjusted or temporarily positioned differently — these are defined exceptions covered in the tool's manual and applicable OSHA standards, not license to remove guards entirely.
What should you do if a power saw guard is damaged?
Take the saw out of service immediately. A damaged guard provides little or no protection — it may give the operator false confidence while failing to cover the blade in the event of a slip. Contact the manufacturer or an authorized service center for replacement parts. Never operate a saw with a cracked, stuck, or missing guard, and never attempt a field repair with tape or improvised materials.
What PPE is required when using a power saw?
At minimum: ANSI-rated safety glasses or a face shield, hearing protection (earmuffs or earplugs), a dust mask or respirator appropriate to the material being cut, and steel-toed footwear on job sites. On commercial construction sites, OSHA may require additional PPE depending on the materials being cut and the work environment. Always follow the specific PPE requirements in the tool's manual and any applicable site safety plan.
What causes kickback on a table saw, and how do guards prevent it?
Kickback occurs when the workpiece binds on the back of the spinning blade — the blade catches the material and hurls it back toward the operator at high speed. The riving knife or splitter prevents kickback by keeping the kerf open behind the blade so the wood can't close on it. Anti-kickback pawls provide a secondary catch: if the material does begin to travel backward, the pawls' teeth bite into the wood and stop the ejection. Neither system works if the guard assembly has been removed.
Conclusion
Keep every safety guard on your power saws in place and working, and replace one that is missing or damaged before you make another cut. Ready to compare models? Browse our full selection of radial arm saws at Iron Line Tools.
Safety and standards references: OSHA 1910.243 guarding of portable powered tools and OSHA 1910.212 general requirements for all machines.
Explore the category: Power Tools and Power Saws.
Related Reading
Shop Radial Arm Saws at Iron Line Tools

Castaly 14" Radial Arm Saw RS-640
Price: $5,269 | Type: Radial Arm Saw
The Castaly RS-640 is a 14" professional radial arm saw with heavy-duty cast iron arm for precision crosscutting and trimming. Built for production woodworking shops that need consistent accuracy.

Maksiwa BMS.1600.IR Sliding Panel Saw
Price: $6,399 | Type: Sliding Panel Saw
The BMS.1600.IR is a high-precision sliding panel saw for shops that need accurate cuts on sheet goods and solid wood. Handles full panels with a sliding table and precision fence system.
Is your blade guard missing or damaged?
Ask our team which protection each circular, table and band saw needs, plus the right safety gear.



