In This Guide
- What Is a Power Saw?
- Circular Saw
- Miter Saw
- Metal Chop Saw
- Reciprocating Saw
- Jigsaw
- Concrete Saw
- Door Jamb Saw (Undercut Saw)
- Types of Power Saws: Comparison Table
- Power Saw Types Compared by Job and Material
- Power Saw Types in Our Store
- How to Choose the Right Power Saw
- Frequently Asked Questions
- Conclusion
Featured power saws

Evolution Power Tools
Evolution Power Tools Single Bevel Sliding Miter Saw R255SMS+
$392.97
Professional sliding compound miter saw with a 15 Amp Hi-Torque motor and a 10 inch multi-material TCT blade, plus laser guidance. It covers the miter saw type for trim and angle work. Check the cut capacity you need before you buy.

Virutex
Virutex Cordless Circular Saw SRB165 7400700
$235.00
Cordless operation and a brushless motor make this circular saw easy to carry between jobs, with precise cutting across a variety of materials. It represents the cordless circular saw type. Compare battery options for the work you do.

Virutex
Virutex Cordless Jig Saw SCB324 3400400
$202.00
Jig saw for precision and mobility with a powerful brushless motor and advanced control systems. It cuts wood, aluminum and steel, the curved cuts the jigsaw section covers. Check the battery and blade type before ordering.

Evolution Power Tools
Evolution Power Tools 9 in. Electric Concrete Saw R230DCT
$224.99
Lightweight by design, this 9 inch electric concrete saw pairs a 15 Amp motor with Power Protect Technology. It is a lighter way into the concrete saw type. Check the cutting depth you need against the blade size before you buy.
What Is a Power Saw?
A power saw is any motorized cutting tool that uses a blade, chain, or abrasive disc to cut through material. Unlike hand saws, power saws use an electric motor — corded or battery-powered — to drive the blade, which means faster cuts, cleaner results, and far less physical effort on long production runs.
The category is broad. A 7¼-inch circular saw and a 9-inch concrete saw are both power saws, but they share almost nothing beyond that motor. Choosing the right type means matching the tool to the material, the cut geometry, and the job environment. This guide walks through every major type and helps you decide which one — or which combination — belongs in your toolkit.
Circular Saw
The circular saw is the most widely used power saw on job sites and in workshops worldwide. A spinning toothed blade cuts through wood, plywood, OSB, and — with the right blade — metal, plastic, and composite materials. Standard blade sizes are 6½ inch and 7¼ inch. Most models bevel to 45 degrees for angled cuts.
Best for: Framing lumber, sheet goods, long rip cuts, cross-cuts on dimensional lumber, job site cutting where portability matters.
Corded vs. cordless: Corded circular saws (13–15 amps) deliver sustained power for heavy production cutting. Cordless models on 18V–40V brushless platforms match corded performance for most cuts and eliminate cord management on job sites. Evolution's multi-material TCT circular saws cut wood, steel, aluminum, and plastic on one blade without changing — a significant advantage for mixed-material work.
Browse circular saws at Iron Line Tools.
Miter Saw
A miter saw — also called a chop saw for wood or a drop saw — mounts a circular blade on a pivoting arm that drops down through the workpiece. The table rotates left and right to set the miter angle; compound miter saws also tilt the head to cut a bevel simultaneously. Sliding compound miter saws add horizontal travel for wider boards.
Best for: Crown molding, door and window casing, baseboards, picture frames, stair stringers, any work requiring precise repeated angle cuts at a fixed station.
Corded vs. cordless: Cordless miter saws on 36V–40V platforms have made corded models largely redundant for framing and finish carpentry. Battery power eliminates the trip hazard and setup time of running a cord to a miter saw station on a job site.
Browse cordless miter saws at Iron Line Tools.
Metal Chop Saw
A metal chop saw — also called a cold cut saw or metal cut-off saw — is purpose-built for cutting steel, iron, aluminum, and other metals. Traditional abrasive chop saws use a grinding disc and generate significant heat and sparks. Cold cut saws use a toothed carbide or TCT blade and cut metal cold — no sparks, no heat-affected zone, no burrs requiring cleanup.
Best for: Steel tube and pipe, angle iron, flat bar, rebar, EMT conduit, aluminum extrusions. Essential on metal fabrication and construction sites where clean cuts on metal stock matter.
Cold cut vs. abrasive: Cold cut saws produce a cleaner, cooler cut with less sparking. The blade lasts significantly longer than an abrasive disc and the cut is ready to weld or finish immediately without grinding. For professional metalwork, a cold cut saw is the better investment.
Browse metal chop saws at Iron Line Tools.
Reciprocating Saw
A reciprocating saw drives a blade back and forth in a linear motion — the same mechanics as a handsaw, but powered at 2,000–3,000 strokes per minute. The blade extends forward from the tool, making it uniquely suited for cutting in tight spaces, overhead, and in positions where no other saw could reach. Blade selection determines the material: wood blades, metal blades, demo blades for nail-embedded wood, and pruning blades for green wood all fit the same tool.
Best for: Demolition, remodeling, pipe cutting, cutting in wall cavities, removing old door frames, rough plumbing and electrical rough-in cuts. The go-to saw when access is the constraint.
Browse cordless reciprocating saws at Iron Line Tools.
Jigsaw
A jigsaw uses a short, narrow reciprocating blade to cut curves, circles, and irregular shapes that no other power saw can follow. It can also make straight cuts, though a circular saw is faster for those. The jigsaw's narrow blade can be plunged into a drilled starter hole to cut interior shapes — sink cutouts, electrical panel openings, countertop holes — without cutting in from an edge.
Best for: Curved cuts, cutouts in countertops and panels, scrollwork, cutting shapes in plywood and sheet goods, tile cutting with the appropriate blade. The most versatile saw for detailed and irregular work.
Browse jigsaws at Iron Line Tools.
Concrete Saw
A concrete saw uses a diamond segmented blade to cut concrete, masonry, brick, stone, and asphalt. The diamond blade grinds through the material rather than cutting it with teeth. Handheld concrete saws handle wall cuts, expansion joints, and demolition work. Walk-behind electric concrete saws handle flat slab work, roadway cutting, and large-scale masonry projects.
Best for: Cutting control joints in concrete slabs, making openings in masonry walls, cutting curbs and pavement, trenching for utilities. Not interchangeable with wood or metal saws — the diamond blade and motor are engineered specifically for masonry work.
Browse concrete saws at Iron Line Tools.
Door Jamb Saw (Undercut Saw)
A door jamb saw — also called an undercut saw — is a specialty tool designed to trim the bottom of door frames and door stops flush with the floor, allowing new flooring to slide underneath without removing the casing. The flat, low-profile base guides the blade horizontally at baseboard height. Without a jamb saw, this cut requires chiseling and hand sawing, which is slow and inconsistent on a large installation job.
Best for: Flooring installation, undercutting door jambs for hardwood, laminate, tile, or carpet installation. An essential specialty saw for any professional flooring installer.
Browse door jamb saws at Iron Line Tools.
Types of Power Saws: Comparison Table
| Saw Type | Primary Cut | Materials | Best Use |
|---|---|---|---|
| Circular Saw | Straight / bevel | Wood, sheet goods, metal (TCT blade) | Framing, sheathing, general cutting |
| Miter Saw | Cross-cut / miter / bevel | Wood, molding, trim, soft metal | Finish carpentry, trim, framing angles |
| Metal Chop Saw | Cross-cut (metal) | Steel, iron, aluminum, pipe | Metal fab, structural steel, conduit |
| Reciprocating Saw | Push-pull / plunge | Wood, metal, pipe, demo materials | Demo, remodel, pipe cutting, tight spaces |
| Jigsaw | Curved / intricate | Wood, plywood, tile, metal, plastic | Cutouts, curves, countertops, shapes |
| Concrete Saw | Straight (masonry) | Concrete, brick, stone, asphalt | Control joints, masonry openings, slabs |
| Door Jamb Saw | Horizontal undercut | Wood door frames and casings | Flooring installation, undercutting jambs |
Power Saw Types Compared by Job and Material
Each type of power saw in the guide has a matching model in our store, and this table lines them up. Look at the Key feature column first, since blade and motor set what each saw can cut.
| Model | Price | Key feature | Best for |
|---|---|---|---|
| Evolution Power Tools Multi-Material Cutting Chop Saw With 14 in. Blade R355CPS | $431.98 | High-torque 15 Amp corded motor and a 14 inch TCT blade | Fast, clean chop cuts with a single TCT blade |
| Virutex Cutting Machine For Doors (120V) RZ270S 7000399 | $750.00 | Adjustable depth for trimming doors, frames and baseboards | Installers trimming doors over parquet or laminate |
| Evolution Power Tools Metal Cutting Circular Saw 7-1/4 in. Blade S185CCSL | $237.15 | Cold Cut Technology steel cutting with a 7-1/4 inch blade | Steel fabrication and heavy-duty metal cutting |
| Evolution Power Tools 12 in. Electric Concrete Saw R300DCT | $423.48 | Heavy-duty professional electric saw built for deep concrete cuts | Contractors cutting concrete without a gas saw |
| Evolution Power Tools Reciprocating Saw with 4 Blades R230RCP | $153.83 | 7 Amp motor, 2,800 SPM, 180 degree rotating handle | Demolition, remodeling and general cutting work |
Start with the material or job in front of you, then follow that row to the saw type with the blade or motor that fits.
Power Saw Types in Our Store
The saws below match the types in this guide: circular, miter, metal chop, reciprocating, jig, concrete and door jamb. Use the comparison table to confirm the material and cut before you buy.
1. Evolution Power Tools Multi-Material Cutting Chop Saw With 14 in. Blade R355CPS — $431.98
Chop saw type in this guide: 15 Amp corded motor, 14 inch blade and cold cut technology for several materials in one saw. View more >
2. Virutex Cutting Machine For Doors (120V) RZ270S 7000399 — $750.00
Adjustable depth and door cutting precision for trimming doors, door frames, baseboards and skirting boards, aimed at installers working with parquet, laminate and ceramic flooring. View more >
3. Evolution Power Tools Metal Cutting Circular Saw 7-1/4 in. Blade S185CCSL — $237.15
Heavy-duty steel cutting with cold cut technology, a 15 Amp motor and a 7-1/4 inch blade, aimed at metal fabrication. View more >
4. Evolution Power Tools 12 in. Electric Concrete Saw R300DCT — $423.48
Concrete cutting is the job here: a 12 inch blade, Power Protect Technology and a heavy-duty build for contractors. View more >
5. Evolution Power Tools Reciprocating Saw with 4 Blades R230RCP — $153.83
Demolition and remodeling work is what the reciprocating type is for, and this corded model adds a 180 degree rotating handle. View more >
How to Choose the Right Power Saw
The right power saw depends on three questions: what material are you cutting, what shape is the cut, and where are you cutting it?
Material: Wood and sheet goods are handled by circular saws, miter saws, and jigsaws. Steel and metal require a metal chop saw or a circular saw fitted with a TCT metal-cutting blade. Concrete and masonry require a concrete saw with a diamond blade — no other blade type will work safely or effectively.
Cut geometry: Straight cuts along or across a board belong to the circular saw or miter saw. Precise angle cuts at a fixed station belong to the miter saw. Curves and irregular shapes belong to the jigsaw. Cuts in tight, awkward, or demolition conditions belong to the reciprocating saw.
Job environment: A permanent shop station can use a corded miter or table saw. A job site with no power source needs cordless tools. Remote or elevated work — cutting a pipe overhead or demolishing a wall cavity — needs a cordless reciprocating saw. Many professionals carry a cordless circular saw and a cordless reciprocating saw as their core portable pair, adding a miter saw on a cart for station work.
Frequently Asked Questions
What are the different types of power saws?
The main types of power saws are: circular saw, miter saw, metal chop saw, reciprocating saw, jigsaw, concrete saw, and door jamb saw. Each type is engineered for a specific combination of material and cut geometry.
What is a power saw used for?
Power saws are used to cut wood, metal, masonry, plastic, and composite materials faster and more accurately than hand saws.
What power saw should a beginner start with?
A cordless circular saw is the most practical first power saw for most people.
What is the difference between a circular saw and a miter saw?
A circular saw is a handheld tool you move across the workpiece. A miter saw is a stationary tool where you bring the workpiece to the saw.
Can a circular saw cut metal?
Yes — with the right blade. A circular saw fitted with a TCT multi-material blade cuts steel, aluminum, and plastic cleanly without sparks.
Conclusion
Every job calls for a different saw, so match the circular saw, miter saw, chop saw, reciprocating saw, jigsaw or concrete saw to the material and the cut. Ready to compare models? Browse our power saws at Iron Line Tools.
Safety and standards references: OSHA 1910.243 guarding of portable powered tools and OSHA 1910.212 general requirements for all machines.
Explore the category: Power Tools.
Related Reading
Shop Professional Power Saws at Iron Line Tools

Castaly 14" Radial Arm Saw RS-640
Price: $5,269 | Type: Radial Arm Saw
A heavy-duty industrial radial arm saw built for precision crosscutting, ripping, and mitre work.

Maksiwa BMS.1600.IR Sliding Panel Saw
Price: $6,399 | Type: Sliding Panel Saw
The BMS.1600.IR is a professional-grade sliding table saw for flawless rip and crosscuts on full sheet goods.
Browse the Full Saw Lineup
Framing walls or cutting steel pipe?
Choose between a door jamb saw, metal chop saw or concrete saw with a quick call to our team.

