Maksiwa BMS.1600.IR sliding table saw overview showing aluminum sliding table and rip fence — a professional-grade table saw used for precision woodworking cuts

How to Use a Table Saw

Knowing how to use a table saw is one of the most valuable skills in professional woodworking and cabinet shop production. Table saws make straight, repeatable rip cuts, crosscuts, bevel cuts, and dado cuts with a level of precision that no other machine can match at that speed. This guide covers everything from table saw basics and parts to setting up the machine, making every cut type, and choosing the right sliding table saws for your shop.

Maksiwa BMS.1600.IR sliding table saw overview showing aluminum sliding table and rip fence — a professional-grade table saw used for precision woodworking cuts

Quick Answer

To use a table saw, set the blade height so the teeth just clear the top of the workpiece, adjust the rip fence or miter gauge for the cut, power on the machine, feed the material steadily through the blade using a push stick for narrow stock, and keep the offcut free from the blade. Table saws are used for rip cuts (along the grain), crosscuts (across the grain), bevel cuts (at an angle), and dado cuts (grooves).

What Is a Table Saw and What Can It Do?

A table saw is a stationary power saw that mounts a circular, motor-driven blade through the center of a flat table surface. The blade projects up through a slot in the table, and the workpiece is fed across the table and into the blade rather than moving the tool across the workpiece. This design creates the stable, guided feed path that makes table saws the most accurate ripping and crosscutting machines in a woodworking shop.

Table saw uses fall into four main categories: rip cuts (cutting along the length of a board with the grain), crosscuts (cutting across the width of a board against the grain), bevel cuts (tilting the blade to cut an angled profile), and dado cuts (cutting a wide, flat-bottomed groove into the face or edge of a board). Advanced woodworkers also use the table saw for rabbets, tenons, tapers, and compound angles. Understanding what you can do with a table saw is the foundation of woodworking production efficiency — no other machine handles straight cuts in solid wood and sheet goods as quickly or repeatedly.

Maksiwa BMD.3200.IR sliding panel saw angled view showing sliding table and crosscut fence

Types of Table Saws

Not all table saws are built for the same application. Knowing the types of table saw designs helps you match the machine to your production demands before you learn how to operate a table saw on a specific model.

Benchtop and Portable Table Saws

Benchtop table saws are lightweight, compact machines designed for job-site use or small shops with limited floor space. They run on 15-amp household circuits and are table saws for beginners who need an affordable entry point. Their small table size limits ripping capacity and makes it difficult to process full 4×8 sheet goods without infeed and outfeed support. Direct-drive motors can lack the torque of cabinet saws when cutting hardwoods at full depth.

Contractor Table Saws

Contractor table saws use a larger blade (typically 10 inches), a larger table, and a more powerful motor than benchtop models. Many have open stands and are still portable enough to move between job sites, though they are heavier than benchtop saws. These are common table saw basics for small cabinet shops and trim carpenters who need more capacity than a benchtop but cannot justify a full cabinet saw.

Cabinet Table Saws

Cabinet table saws mount the motor inside a fully enclosed, heavy cast-iron cabinet. The enclosed cabinet provides superior dust collection because the entire blade area is sealed. The heavy mass reduces vibration, improving cut quality on hardwoods. Cabinet saws accept dado stacks and are the workhorse table saw for professional woodworking shops that run production all day.

Sliding Panel Saws (Sliding Table Saws)

Sliding panel saws add an aluminum sliding carriage to the left of the main blade, allowing full 4×8 sheets of plywood, MDF, and melamine to be cut accurately without an outfeed table. The sliding table moves the workpiece precisely through the blade rather than the operator pushing the sheet across the fixed table. This eliminates binding, tear-out, and fence-creep that commonly cause errors when ripping large panels on a standard contractor or cabinet saw. For production cabinet shops, furniture manufacturers, and millwork operations, sliding table saws are the professional standard for panel processing.

Parts of a Table Saw and Their Functions

Understanding table saw parts and functions helps you operate the machine safely and accurately. This table saw anatomy overview covers every major component.

Main Blade and Scoring Blade

The main blade is the primary circular saw blade that makes the full-depth cut through the workpiece. The scoring blade — standard on sliding panel saws and cabinet saws designed for panel work — is a small, independent blade mounted below and in front of the main blade. It scores the bottom face of the panel before the main blade cuts through, eliminating tear-out on veneered surfaces. This is one of the most important table saw parts for furniture and cabinet work where both faces of a panel need to remain clean.

Saw blade and scoring blade assembly on the Maksiwa BMS.1600.IR sliding table saw — close-up view of table saw parts showing main blade and scoring unit

Rip Fence

The rip fence is a straight metal guide that runs parallel to the blade along the right side of the table. For rip cuts, you set the fence to the desired width, lock it in place, and feed the workpiece with the board's edge against the fence. The rip fence must be precisely parallel to the blade — a fence that is not square causes the board to bind against the blade during the cut, which is a leading cause of kickback. On sliding panel saws, the rip fence is a large, precision-engineered aluminum fence with a digital readout or rule that allows fast, accurate width settings.

Adjustable crosscut fence support arm on the Maksiwa BMS.1600.IR sliding table saw — table saw parts showing precision fence system for accurate crosscuts

Sliding Table (Carriage)

The aluminum sliding table is a precision-ground carriage that travels on linear bearings parallel to the blade. The workpiece is placed and clamped (or held) on the sliding table, and the operator pushes the carriage through the blade for a crosscut. Because the work travels with the table rather than being pushed across a fixed surface, the cut is free from fence pressure and lateral movement, producing clean, square crosscuts on even very wide panels. On professional sliding panel saws, the carriage travels 3,200 mm or more of stroke length.

Maksiwa BMS.3200.IR aluminum sliding table extrusion detail on a sliding panel saw

Blade Guard and Riving Knife

The blade guard covers the top of the blade and prevents incidental contact during the cut. The riving knife is a curved metal plate mounted directly behind the blade, in the saw kerf. As the wood passes through the blade, the riving knife keeps the kerf open and prevents the two sawn faces from pinching back against the blade — the primary mechanical cause of kickback. These are among the most critical parts of a table saw from a safety standpoint. On sliding panel saws, an integrated blade guard rides up and down with the blade height adjustment and is designed to stay in position for virtually every standard cut.

Blade Height and Tilt Handwheels

Two handwheels on the front or side of the machine control blade height (how far the blade projects above the table) and blade tilt (the angle of the blade relative to vertical, for bevel cuts). Both are critical adjustments before every cut. The blade height wheel raises or lowers the arbor assembly; the tilt wheel pivots the arbor left or right up to 45 degrees (and on some models 47 degrees to allow for positive-stop trim cuts).

Table Saw Safety and Kickback Prevention

Learning how to use a table saw safely begins with understanding kickback — the most dangerous event that can occur at a table saw. Kickback happens when the blade catches the workpiece and hurls it back toward the operator at the blade's tip speed, which can exceed 100 miles per hour. Table saw safety rules exist to eliminate the conditions that cause kickback. OSHA table saw guidance calls for a self-adjusting guard over the blade above the table, a guard on the blade below the table, a spreader when ripping, anti-kickback fingers, and a push stick for small pieces and for pushing stock past the blade; the machine guarding rules for hand-fed saws are in 29 CFR 1910.213.

What Causes Kickback?

Kickback is caused by one of three conditions: the saw kerf closing and pinching the blade (wood under internal stress), the offcut riding up the back of the blade teeth, or the operator feeding the board at an angle that traps it between the blade and the fence. All three are preventable with correct setup and technique. OSHA also lists incorrect blade height, poor blade maintenance, missing safeguards, and poor-quality lumber among the causes of kickback.

Blade guard and riving knife assembly on the Maksiwa BMT.3200.IR sliding table saw

How to Prevent Kickback

  • Keep the riving knife in place. Never remove it except for dado cuts that require a wide kerf below table surface.
  • Never use the rip fence and miter gauge simultaneously. This traps the offcut between the fence and blade and is the leading cause of crosscut kickback.
  • Stand to the side of the blade line. Do not stand directly behind the blade where a kickback projectile would travel.
  • Use a push stick for narrow rip cuts. When ripping stock narrower than 4 inches, the push stick keeps hands away from the blade.
  • Keep the fence parallel to the blade. Check fence alignment regularly, especially after the fence is moved to a new position.

Essential PPE for Table Saw Work

How to properly use a table saw requires wearing the right personal protective equipment every time: safety glasses or a face shield (sawdust and splinters move at blade speed), hearing protection (table saw motor noise exceeds 100 dB), and no loose clothing, jewelry, or gloves that could catch on the blade. Anti-fatigue mats improve footing during long production runs.

Woodworker operating the Maksiwa BMS.3200.IR sliding table saw in a professional workshop — proper operator position demonstrates safe table saw use technique

How to Set Up a Table Saw Step by Step

Correct table saw set up before each session prevents the alignment errors that cause kickback, out-of-square cuts, and blade damage. This is the table saw basics setup sequence used by professional cabinet shops.

Step 1: Adjust Blade Height

Set the blade so the teeth project about 1/8 inch above the top face of the workpiece. Higher blade height creates a more aggressive cut angle that increases kickback risk; lower height reduces cutting efficiency and can cause the blade to rub rather than cut cleanly on thicker stock. Use the front handwheel to raise or lower the blade with the machine powered off.

Front control panel and blade height handwheel on the Maksiwa BMS.1600.IR sliding table saw

Step 2: Adjust Blade Angle

For standard cuts, confirm the blade is at 90 degrees to the table surface using a reliable square against the blade body (not the teeth). Use the tilt handwheel to correct any deviation. For bevel cuts, set the angle to the target value and check the positive stop. Most cabinet and sliding panel saws have positive stops at 90 and 45 degrees.

Close-up of blade height and tilt adjustment controls on the Maksiwa BMS.3200.IR sliding table saw — step by step table saw setup for accurate cuts

Step 3: Set the Rip Fence

Measure from the blade's near tooth (the tooth closest to the fence) to the fence face using a tape or the fence's built-in rule. Lock the fence at the desired width. Run a test cut in scrap and measure the offcut to verify accuracy before running production material.

Step 4: Check Alignment

Use a dial indicator or the same two-point measurement technique to confirm the rip fence is parallel to the blade from front to back. Measure from the same tooth at the front of the blade and at the back of the blade to the fence face; both measurements should be identical. Any discrepancy above 0.005 inches should be corrected before cutting, especially on a production sliding panel saw where repeated cuts will amplify a small fence error across dozens of panels.

How to Make a Rip Cut

A rip cut runs along the grain of a board, cutting it to a narrower width. Using a table saw to rip boards is the machine's most common use in production woodworking — ripping rough lumber to finished width, ripping hardwood to strip widths, and ripping sheet goods to cabinet width dimensions.

Which Side of the Line to Cut On

Table saw which side to cut is determined by which edge is the reference edge against the rip fence. The reference edge rides along the fence. This means your rip cut will be on the opposite side of the blade from the fence. Always mark the width you want to keep on the fence side of the blade, not the offcut side, to avoid confusion about cut placement.

Rip Cut Step by Step

  • Set blade height to 1/8 inch above the workpiece.
  • Set the rip fence to the desired cut width and lock it.
  • Stand to the left side of the blade line, not directly behind it.
  • Power on the saw and let the blade reach full speed before feeding material.
  • Feed the board with consistent, even pressure, keeping the reference edge flat against the fence.
  • As the board passes the back of the blade, use a push stick to complete the cut — never use your fingers to push narrow stock past the blade.
  • Let the offcut fall free; never reach past the blade to remove it while the blade is spinning.

How to Make a Crosscut

A crosscut runs perpendicular to the grain, cutting a board to length. Using a table saw for crosscuts requires either a miter gauge (for standard saws) or the sliding carriage (for sliding panel saws). Never use the rip fence as a length stop directly against the board during a crosscut — this traps the offcut between the blade and fence, the classic cause of crosscut kickback.

Using the Sliding Table Carriage

On a sliding panel saw, place the board on the sliding carriage with its end against the crosscut fence. Set the crosscut fence to the desired cut length using the built-in flip stop or measuring scale. Hold the workpiece flat on the carriage and push the carriage through the blade in one smooth motion. The carriage returns to start position and the board is lifted clear. This technique produces crosscuts square to within fractions of a millimeter, even on boards 48 inches wide, because the blade is stationary and the work travels in a linear path.

Adjustable crosscut fence support arm on the Maksiwa BMS.3200.IR sliding table saw — accurate crosscut fence positioning for square table saw cutting guide

Using a Miter Gauge

Standard table saws use a miter gauge that slides in a T-slot milled into the table surface. Set the miter gauge to 90 degrees, hold the board against the gauge face, and push both the gauge and workpiece through the blade. For repetitive crosscuts to the same length, attach a stop block to the rip fence ahead of the blade (not beside it) or clamp one to a crosscut sled to register the board without trapping the offcut.

Crosscut fence stop with adjustment handle on the Maksiwa BMP.3200.IR sliding panel saw

How to Cut Angles and Bevels on a Table Saw

Two types of angled cuts are made on a table saw: miter cuts (the blade stays vertical but the board is fed at an angle using the miter gauge) and bevel cuts (the blade tilts while the feed direction stays straight). A compound miter cut does both simultaneously.

How to Use a Table Saw to Cut a 45-Degree Angle

To cut a 45-degree bevel, loosen the blade tilt lock and turn the tilt handwheel until the angle indicator reads 45 degrees. Most cabinet and sliding panel saws have a positive detent at 45 degrees; feel for it and confirm with a bevel gauge. For a miter cut, set the miter gauge to 45 degrees and feed the board at that angle across the blade. For picture frames, door casings, and any application where two 45-degree cuts must meet cleanly, run a test cut first and check the resulting angle against a carpenter's square before committing to production stock.

Blade tilt handwheel on the Maksiwa BMS.3200.IR sliding table saw for setting a 45-degree bevel

Through Cuts vs. Non-Through Cuts

A through cut on a table saw passes all the way through the workpiece from face to face. A non-through cut, sometimes called a blind cut or stopped cut, begins and ends at defined points along the board, leaving the board intact outside the cut zone. Blind dados, tenon shoulders, and decorative grooves are made as non-through cuts by marking the start and stop points on the table and lowering or raising the workpiece carefully with the blade spinning — a technique that requires a climbing cut fence block and a slow, controlled plunge.

Dado Cuts on a Table Saw

A dado is a wide, flat-bottomed groove cut into the face or edge of a board, used for shelves, cabinet bottoms, tongue-and-groove joints, and drawer bottom grooves. Dado cuts on a table saw use either a stacked dado head (a set of chippers and outside blades that creates a wide kerf in one pass) or a wobble dado (a single blade offset on its arbor to sweep a wide path).

Sliding panel saws designed for dado work — such as the Maksiwa BMS.3200.IR Dado Edition — include a scoring unit that can be adjusted to match the dado width, eliminating tear-out on veneered panels where a dado intersects the face veneer. To cut a dado, remove the standard blade, install the dado stack to the desired width, set blade height to the dado depth, and make the cut using the rip fence as a guide for the groove's position. For through-panel dados, use the crosscut fence on the sliding carriage to ensure the groove runs perfectly perpendicular to the board's edge.

Maksiwa BMT.3200.IR sliding table saw with blade guard, scoring unit and precision fence

Table Saw Types Compared

This table saw cutting guide compares the four main types by capacity, best use case, and what types of table saw cuts each handles best.

Type Rip Capacity Sheet Goods Dado Stack Best For
Benchtop Up to 24″ Partial sheets Limited Beginners, job sites
Contractor Up to 30″ Partial sheets Yes Small shops, trim work
Cabinet Up to 52″ With outfeed support Yes Production woodworking
Sliding Panel Saw Full 4×8 sheets Full sheets, unsupported Yes (w/ Dado Edition) Cabinet shops, panel mills

Sliding Panel Saw Models Compared

These are the Maksiwa sliding panel saws featured in this guide. Specs and prices come from each product page.

Model Key specs Price
Maksiwa BMS.1600.IR Sliding Panel Saw 5 HP main + 1 HP scoring motor, 63" sliding table, 63" crosscut, 35.5" rip, 1-phase 220V / 30A $6,399
Maksiwa BMS.3200.IR Dado Edition Sliding Panel Saw 5 HP main + 1 HP scoring motor, 126" crosscut, 51" rip, 8" dado stacks, 1-phase 220V (22A) or 3-phase 220V (11A) $8,999
Maksiwa BMT.3200.IR TITANIUM Sliding Panel Saw 5 HP main + 3/4 HP scoring motor, 126" crosscut, 51" rip, 3-1/2" max cut height, 1-phase 220V / 30A $10,999
Maksiwa BMP.3200.IR Platinum Sliding Panel Saw 7.5 HP main + 3/4 HP scoring motor, 126" crosscut, 51" rip, 3-phase 220V / 30A $12,499

Top Table Saw Picks

For professional cabinet shops and furniture manufacturers, these three Maksiwa sliding panel saws represent the best balance of capacity, accuracy, and production efficiency in the sliding table saw category.

1. Maksiwa BMS.1600.IR Sliding Panel Saw — $6,399.00

The BMS.1600.IR is the most compact of the Maksiwa sliding panel saws. It has a 5 HP main motor (4,000 RPM), a 12-inch main blade, and a 1 HP scoring motor with a conical scoring blade that reduces chip-out on melamine and veneered panels. Rip capacity is 35 1/2 inches, crosscut capacity is 63 inches, and the cast iron table pairs with a 63 x 12 inch sliding table. The Dado Edition accepts an 8-inch dado blade up to 3/4 inch wide and runs on 1-phase 220V. For shops moving from a contractor saw to their first sliding panel saw, it adds panel-sizing accuracy in a smaller footprint than the 126-inch models. View more >

2. Maksiwa BMS.3200.IR Dado Edition Sliding Panel Saw — $8,999.00

The BMS.3200.IR Dado Edition has a 126-inch crosscut capacity and a 126 x 14 3/4 inch sliding table, so it can support full sheets through the cut. It has a 5 HP main motor (4,000 RPM), a 1 HP scoring motor with a conical scoring blade, a 51-inch rip capacity, and accepts an 8-inch dado blade for grooves and rabbets. Controls include a digital angle display, separate switches for the main and scoring motors, and emergency stops at the front and back. The crosscut fence comes with two flip stops, and the saw is offered in 1-phase or 3-phase 220V. View more >

3. Maksiwa BMD.3200.IR Diamond High Performance 10 HP Sliding Panel Saw — $20,999.00

The BMD.3200.IR Diamond is the top model of the Maksiwa sliding panel saws. It has a 10 HP (7.3 kW) main motor with 3,000, 4,000 and 5,000 RPM blade speeds, takes blades up to 14 inches, and adds a 3/4 HP scoring motor. Rip capacity is 51 inches and the 126-inch aluminum sliding table rides on linear guide rails. A touchscreen controls blade height, tilt and machine functions, and the CNC-controlled rip fence has a manual mode when you need it. It runs on 3-phase 220V at 40 amps. It is built for cabinet, furniture and custom production shops that cut large panels all day. View more >

Front view of the Maksiwa BMD.3200.IR sliding panel saw with blade guard and support table

How to Choose the Right Table Saw

Choosing the right table saw for your shop depends on the volume of work, the material you cut most, and the size of panels you process. Work through these four factors to narrow your choice.

  • Sheet goods volume: If you process full 4×8 panels regularly — plywood, MDF, melamine — a sliding panel saw is the right choice. It handles sheet goods faster and more accurately than any standard table saw because the sliding carriage eliminates manual sheet control. If you mostly cut solid lumber with occasional partial-sheet cuts, a cabinet saw is a better fit.
  • Material hardness and thickness: Hardwoods and thick MDF demand more motor power. For continuous production in hard maple, white oak, or 1-inch-thick MDF, a saw with 5 HP or more will maintain blade speed throughout the cut. Underpowered saws slow the blade under load, increasing the chance of burn marks and poor cut quality.
  • Dado cutting requirements: If your shop builds frameless cabinets with dadoed shelf standards and drawer bottoms, a sliding panel saw with dado capability (like the BMS.3200.IR Dado Edition) saves the time of maintaining a separate dado station. Confirm the saw's arbor accepts the dado stack width you need.
  • Floor space: A 3,200 mm sliding panel saw requires 10–12 feet of clear floor in front of and behind the machine for the carriage to travel and for infeed/outfeed material to extend. Plan floor space before purchasing.

For most professional cabinet and millwork shops, an upgrade to sliding table saws is the single change that most improves panel processing accuracy and throughput. The investment in a sliding panel saw typically pays back in reduced material waste and faster production within the first year for shops processing more than 10 sheets per day.

Maksiwa BMP.3200.IR Platinum sliding panel saw with outrigger table, angled overview

Frequently Asked Questions

What are the main types of table saw cuts?

The main types of table saw cuts are rip cuts (cutting along the wood grain to reduce board width), crosscuts (cutting across the grain to reduce board length), bevel cuts (angling the blade to cut a profile across the board's face or edge), and dado cuts (cutting a wide groove into the face of a board for joinery). Each cut uses a different setup: rip cuts use the rip fence, crosscuts use the miter gauge or sliding carriage, bevel cuts require adjusting the blade tilt handwheel, and dado cuts use a stacked dado head in place of the standard blade.

How do you prevent kickback on a table saw?

Table saw kickback is prevented by keeping the riving knife in place behind the blade to hold the kerf open, never using the rip fence and miter gauge for a crosscut simultaneously (which traps the offcut), standing to the side of the blade rather than directly behind it, using a push stick for narrow rip cuts, and ensuring the rip fence is set parallel to the blade before every session. Using properly sharpened blades with the correct tooth geometry for the material also reduces blade grabbing and reduces kickback risk on problem cuts.

What is a sliding table saw and how is it different from a standard table saw?

A sliding table saw, also called a sliding panel saw, adds a precision aluminum carriage to the left of the main blade that travels on linear bearings parallel to the blade. The workpiece rides on the carriage through the blade, rather than being pushed across a fixed table. This eliminates the manual effort and alignment error of feeding large panels freehand, produces cleaner crosscuts because there is no lateral workpiece movement, and handles full 4×8 sheets of plywood and MDF accurately without an outfeed table. Standard table saws require the operator to fully support and guide the workpiece, limiting accuracy on wide panels; sliding panel saws guide the work mechanically, making sheet goods processing faster and more precise.

How do you use a table saw to cut a 45-degree angle?

To cut a 45-degree bevel on a table saw, loosen the blade tilt lock and turn the tilt handwheel until the angle indicator reads 45 degrees — most saws have a positive detent at exactly 45 degrees. Confirm the angle with a bevel gauge against the blade body. For a miter cut at 45 degrees (blade stays vertical, board fed at an angle), set the miter gauge to 45 degrees. Run a test cut on scrap material first and confirm the two sawn faces meet at exactly 90 degrees before cutting production stock. Compound miter cuts that are both beveled and mitered require adjusting both the tilt handwheel and the miter gauge simultaneously.

What should beginners know before using a table saw for the first time?

Table saws for beginners should start with these fundamentals: always wear safety glasses and hearing protection; set blade height to no more than 1/8 inch above the workpiece; keep the riving knife in place for every rip cut; use a push stick for any rip cut narrower than 4 inches; never stand directly behind the blade; and do not start the cut until the blade has reached full speed. Table saw tips for beginners also include always making a test cut in scrap before cutting expensive material, allowing the blade to come to a complete stop before reaching across the table, and keeping the table surface clear of offcuts that could contact the spinning blade during the next cut.

Conclusion

Knowing how to use a table saw transforms shop efficiency — from ripping rough lumber to ripping sheet goods to cutting precision joinery, the table saw is the machine that underpins nearly every other woodworking operation. For professional shops that process panels daily, a sliding panel saw takes that efficiency further by handling full-sheet cuts accurately, repeatably, and without the alignment errors that plague standard table saws on wide material. Explore our complete line of professional sliding table saws to find the right machine for your production volume and panel size.

Browse Table Saws by Type

Explore the category: Power Tools and Power Saws.

Talk to a Table Saw Specialist

Not sure which sliding panel saw fits your shop's production volume and panel size? Our specialists will help you match the right machine to your operation.

888-308-5580

Featured Sliding Table Saws

Maksiwa BMS.1600.IR Dado Edition sliding panel saw from the rear — a compact sliding table saw for cabinet shops that cut sheet goods

Maksiwa

Maksiwa BMS.1600.IR Sliding Panel Saw

$6,399.00

The most compact Maksiwa sliding panel saw in this guide. The Dado Edition has a 5 HP main motor, a 1 HP scoring motor, a 63-inch crosscut capacity, a 35 1/2-inch rip capacity and room for an 8-inch dado blade, and it runs on 1-phase 220V at 30 amps.

View Product
Maksiwa BMS.3200.IR Dado Edition sliding table saw — full-length sliding table for cutting large panels and dado grooves

Maksiwa

Maksiwa BMS.3200.IR Dado Edition Sliding Panel Saw

$8,999.00

The Dado Edition pairs a 126-inch crosscut capacity and a 126-inch sliding table with a 5 HP main motor, a 1 HP scoring motor and an 8-inch dado blade capacity. It is offered in 1-phase or 3-phase 220V, with a digital angle display and emergency stops at the front and back.

View Product
Maksiwa BMT.3200.IR TITANIUM sliding panel saw — underside view showing heavy-duty steel frame and support structure for professional table saw production use

Maksiwa

Maksiwa BMT.3200.IR TITANIUM Sliding Panel Saw

$10,999.00

The BMT.3200.IR TITANIUM has a 126-inch crosscut capacity and a 126 x 14 inch sliding table, a 5 HP main motor (4,000 RPM) that runs on 1-phase 220V, a 3/4 HP scoring motor with a conical scoring blade, and a 51-inch rip capacity. It includes a dual overhead guard and two 4-inch dust ports (1,000 CFM minimum) and is aimed at cabinet and furniture shops cutting sheet goods every day.

View Product
Front three-quarter view of the Maksiwa BMP.3200.IR sliding panel saw with full table support

Maksiwa

Maksiwa BMP.3200.IR Platinum Sliding Panel Saw

$12,499.00

The BMP.3200.IR PLATINUM has a 7.5 HP main motor on 3-phase 220V, a 3/4 HP scoring motor, a 126-inch sliding table on linear guide rails, and a 51-inch rip fence with a digital readout and micro-adjust. It includes two overhead guards (90 degree and 45 degree) with quick-change, swing-away mounting, and takes blades up to 14 inches.

View Product

Shop All Sliding Table Saws

Explore our complete collection of professional sliding panel saws from Maksiwa — the precision table saw solution for cabinet shops, furniture manufacturers, and panel mills.

Shop Sliding Table Saws

Looking at other types? Browse all table saws.

Questions? Call us: 888-308-5580

How-to guides, Table saws