How to Use a Jigsaw Tool: A Complete Beginner's Guide

A jigsaw is one of the most versatile tools in any woodworker's shop. It cuts curves, straight lines, circles, and complex shapes in wood, metal, plastic, and laminate. If you've never used one, this guide walks through everything: how a jigsaw works, how to set it up, and how to make clean, accurate cuts.

Featured Jigsaw Tool

Virutex Cordless Circular Saw SRB165 7400700 angled view showing compact design with blade guard and ergonomic handle

Virutex

Virutex Cordless Circular Saw SRB165 7400700

$235.00

Use it for straight cuts and keep the jigsaw for curves: this cordless circular saw has a brushless motor, longer runtime and precise cutting across a variety of materials. It comes from the same maker as the cordless jig saw. Check the battery you need.

View Product

Evolution Power Tools Reciprocating Saw with 4 Blades R230RCP featuring a powerful corded reciprocating saw with four included blades for wood, metal, and demolition cutting applications.

Evolution Power Tools

Evolution Power Tools Reciprocating Saw with 4 Blades R230RCP

$153.83

Demolition, remodeling and rough cutting are the jobs of this corded reciprocating saw, with a 7 Amp motor, variable speed and 2,800 SPM. The 4 blades included are a reminder that blade choice drives results. Use a jigsaw for fine curves instead.

View Product

Evolution Power Tools Multi-Material Cutting Circular Saw 7-1/4 in. Blade R185CCSX with guide track, engineered for precise multi-material cutting in wood, metal, plastic, and composite materials.

Evolution Power Tools

Evolution Power Tools Multi-Material Cutting Circular Saw 7-1/4 in. Blade R185CCSX

$223.75

Multi-material cutting with a 7-1/4 inch blade, a 15 Amp motor and an included 3 ft 4 in guide track gives you straight, guided cuts that a handheld jigsaw cannot match. It cuts to a 2-1/2 inch depth. Pair track cuts with a jigsaw for curves.

View Product

What Is a Jigsaw Tool?

A jigsaw is a handheld power saw that cuts with a short, narrow blade that moves up and down in a reciprocating motion. Unlike a circular saw, which cuts in a single straight direction, the jigsaw's narrow blade lets you steer the cut into curves, arcs, angles, and intricate patterns — shapes that no other handheld saw can cut easily.

Proxxon DS 115/E scroll saw main view -- a scroll saw uses the same reciprocating up-and-down blade motion as a jigsaw, illustrating how a narrow reciprocating blade navigates curves and intricate shapes that wider blades cannot follow; the narrow blade width is the defining feature of both scroll saws and jigsaws that enables the curved and pattern cuts described above

The speed of the up-and-down blade motion is controlled by the trigger: press harder to cut faster, ease off for more control. Most jigsaws also offer an orbital action mode in which the blade moves slightly forward into the material on each upstroke, creating a more aggressive cut that removes material faster in softer woods and plastics.

RIKON 10-622VS scroll saw main view showing the reciprocating blade mechanism and table -- the blade drive and tensioning system here operates on the same principle as a jigsaw: a motor drives the blade in a rapid up-and-down stroke; adjusting stroke speed changes cutting aggressiveness, the same concept a jigsaw trigger provides; orbital action on a jigsaw adds a forward lean to each upstroke, matching the geometry of an aggressive cut setting

What Is a Jigsaw Tool Used For?

A jigsaw is the right tool whenever you need to cut a shape that isn't a simple straight line:

  • Curved cuts: Templates, scrollwork, rounded furniture parts, decorative edges
  • Internal cutouts: Sink openings in countertops, outlet holes in cabinetry, speaker cutouts
  • Irregular shapes: Patterns traced from a template, free-form artistic cuts
  • Plunge cuts: Starting a cut in the middle of a panel without drilling a starter hole
  • Metal cutting: Sheet metal, pipe, and thin steel plate with a metal-specific blade
  • Laminate and tile: Specialty downcut blades reduce chipping on finished surfaces
  • Straight crosscuts: While not its primary use, a jigsaw can crosscut boards when a guide fence is attached

A jigsaw is not the best choice for precision straight cuts over long distances (a circular saw or table saw is better) or for ripping boards to width. Its strength is versatility in cutting shapes — what a hand coping saw does, but powered and precise.

Proxxon DS 115/E scroll saw detail view showing blade and work table -- the coping saw comparison above describes how both tools cut curves with a narrow reciprocating blade; the Proxxon DS 115/E here shows the precision a fine reciprocating blade achieves on curved cuts: the blade tracks along a drawn line and the operator steers the cut, exactly the way a jigsaw operator guides the tool along a template or freehand curve

Parts of a Jigsaw

Part What It Does
Blade clamp Spring-loaded clamp that holds the blade in place. Tool-free on modern jigsaws.
Shoe (base plate) The flat plate that rests on the workpiece surface. Can be tilted for bevel cuts (typically 0–±45°).
Trigger Controls motor speed. Variable speed on most models — pressing harder increases blade speed.
Orbital action selector Adjusts blade motion from straight up-down to increasingly aggressive forward-arcing cuts.
Speed dial Sets the maximum blade speed. Lower speeds for metal; higher speeds for wood and soft materials.
Dust blower Blows sawdust away from the cut line so the pencil mark stays visible.
LED work light Illuminates the cut area. Standard on mid-range and better jigsaws.
RIKON 10-622VS scroll saw additional view showing blade clamp, table tilt mechanism, and upper arm -- the functional components visible here correspond directly to the jigsaw parts table above: the blade clamp secures the blade shank; the tilt mechanism mirrors a jigsaw shoe bevel adjustment; the enclosed motor housing drives the blade stroke; both tools share these core components, differing mainly in that the jigsaw is handheld while the scroll saw uses a fixed-arm mounted blade

Beginner Jigsaw and Saw Options Compared

This table puts the jigsaw and saws from our store that the picks cover side by side. Look at the type of cut first, curves for the jigsaw and straight or miter cuts for the others.

Model Price Key feature Best for
Virutex Cordless Jig Saw SCB324 3400400 $202.00 Mobility and advanced control in a compact high-performance body First-time users cutting clean curves in wood or metal
Evolution Power Tools Single Bevel Sliding Miter Saw R185SMS+ $273.63 Lightweight and portable with a 10 Amp motor Portable miter cuts for contractors and DIY users
Evolution Power Tools Metal Cutting Chop Saw With 14 in. Mild Steel Blade S355CPSL $575.97 Cold metal cutting with a 45 degree miter capacity and TCT blade Tubing, angle iron and channel cuts
Virutex Cutting Machine For Doors (120V) RZ270S 7000399 $750.00 Precise trimming of door frames and skirting boards Trim carpenters fitting doors, frames and skirting

Match the cut you want to learn, curves or straight and miter cuts, to a row, then use the key feature to pick a tool that fits your first projects.

Beginner-Friendly Jigsaw and Saw Options

Learning to use a jigsaw is easier with the right blade and a steady cut. Our store carries a cordless jig saw and other saws for the straight cuts and special jobs a jigsaw does not handle.

1. Virutex Cordless Jig Saw SCB324 3400400 — $202.00

Controls and a brushless motor help beginners follow a line, and the saw cuts wood, aluminum and steel cleanly, so match the blade to the material. View more >

2. Evolution Power Tools Single Bevel Sliding Miter Saw R185SMS+ — $273.63

Straight, angled cuts are the job of this 10 Amp sliding compound miter saw, with laser guided precision and a single blade for several materials. View more >

3. Evolution Power Tools Metal Cutting Chop Saw With 14 in. Mild Steel Blade S355CPSL — $575.97

Chop saw with a 14 inch mild steel blade, a 15 Amp motor and 45 degree miter capacity for cutting tubing and angle iron cleanly, a job better suited to it than a jigsaw blade. View more >

4. Virutex Cutting Machine For Doors (120V) RZ270S 7000399 — $750.00

Door cutting machine with adjustable depth for trimming doors, door frames, baseboards and skirting boards, a specialist tool for when a jigsaw cut would not be clean enough. View more >

Choosing the Right Blade

Blade selection is the most important variable in jigsaw performance. The wrong blade causes rough cuts, splintering, blade breakage, and overheating. The key specs to know:

Teeth Per Inch (TPI)

  • High TPI (10–20+): More, smaller teeth = smoother cut. Use for finish work, hardwood, and materials prone to chipping (plywood, laminate).
  • Low TPI (4–8): Fewer, larger teeth = faster, rougher cut. Use for rough carpentry, softwood, and cuts that will be trimmed or sanded afterward.
Proxxon coarse 10 TPI scroll saw blades -- coarse blades with fewer, larger teeth remove material faster and suit rough cuts in softwood; the TPI principle is the same for jigsaw blades: fewer teeth per inch means faster, more aggressive cutting with a rougher finish, appropriate for rough carpentry cuts that will be trimmed or sanded as described above
Material Blade Type TPI Range Speed Setting
Softwood (rough cuts) Wood blade, coarse 4–6 TPI High
Hardwood (finish cuts) Wood blade, fine 10–12 TPI Medium-High
Plywood / laminate Downcut or fine tooth 10–20 TPI Medium
Metal / pipe Bi-metal or HSS blade 18–24 TPI Low
Plastic / PVC Fine tooth or plastic blade 10–14 TPI Medium
Proxxon 28056 HSS jigsaw blades, pack of 2 -- HSS (high-speed steel) jigsaw blades are the metal-cutting choice shown in the blade selection table above: HSS blades maintain a sharper edge longer when cutting metal and hard plastics than standard carbon-steel blades; the fine tooth count corresponds to the 18-24 TPI metal row, and the HSS material resists the heat generated when cutting metal at low jigsaw speed settings

How to Use a Jigsaw: Step-by-Step

Step 1: Put On Your Safety Gear
Before touching the jigsaw: put on safety glasses or a face shield to protect against chips and splinters, hearing protection for extended sessions, and a dust mask if cutting materials that generate fine dust. Tie back loose hair and remove jewelry.
Proxxon normal 18 TPI scroll saw blades -- the 18 TPI blade shown here cuts at a medium tooth count for general wood cutting; blade selection is the first preparation step after donning safety gear: a properly selected blade reduces the risk of breakage, kickback, and excessive chips that safety glasses and hearing protection in Step 1 are designed to guard against
Step 2: Choose and Install the Blade
With the saw unplugged (or battery removed), select the correct blade for your material. Open the blade clamp, slide the blade shank into the clamp slot until it seats fully, and close the clamp. Give the blade a light tug to confirm it's locked. Inspect the blade for bends or chips before installing — damaged blades should be discarded.
Proxxon 28054 special steel jigsaw blades, pack of 2 -- these T-shank jigsaw blades are the type installed in Step 2: the T-shank fitting slides into the blade clamp and locks with a lever release; inspecting before installation means checking the shank for damage, the blade body for bends, and confirming no teeth are missing or cracked; special-steel blades like these are the standard choice for wood cuts and are what to inspect before each use
Step 3: Mark and Secure the Workpiece
Mark your cut line clearly with a pencil. Clamp the workpiece to a sawhorse or workbench so it won't shift during the cut. Raise it slightly — place it on two pieces of scrap wood or over the bench edge — so the blade has clearance below the cut without hitting the work surface. Work in a well-ventilated area if cutting plastic, metal, or composite materials.
Step 4: Set Orbital Action and Speed
For rough cuts in softwood or plywood, set the orbital action to a medium or high setting for faster material removal. For curved cuts requiring precision, set orbital action to 0 (straight) so the blade tracks cleanly around the line. For metal, use orbital 0 and the lowest speed setting on the dial. For wood, use medium-to-high speed.
Proxxon fine 25 TPI scroll saw blades -- fine 25 TPI blades are the equivalent of high-TPI metal and finish-cut jigsaw blades referenced in Step 4: at orbital 0 and low speed, a jigsaw with a fine-tooth blade produces clean cuts in metal with minimal heat buildup; the 25 TPI tooth count removes thin chips on each stroke, reducing deformation on thin sheet metal and plastic that coarser blades would tear
Step 5: Start the Cut
Rest the shoe flat on the edge of the material near the cut line, with the blade positioned just outside the waste side of the line and not touching the material. Pull the trigger and let the blade reach full speed before advancing into the material. Starting the blade while it's in contact with the wood causes chipping, kickback, and rough cuts at the entry point.
Step 6: Guide the Cut
With the blade at full speed, ease the saw forward into the cut. Keep the shoe pressed firmly to the surface throughout — lifting the shoe tilts the blade and causes uneven cuts. Guide the saw along the outside of the pencil line, removing material from the waste side. Use light forward pressure only; do not force the saw. Let the blade's speed and tooth count do the work. Forcing the blade causes it to bend, heat up, and break.
Proxxon spiral scroll saw blades -- spiral blades cut in all directions simultaneously because teeth spiral around the entire blade perimeter; this illustrates the mechanical principle behind the Step 6 warning: a blade under lateral stress from forcing the saw or turning too sharply experiences multi-directional loading; on a straight jigsaw blade, sideways force causes bending and heat at the shank, which is why Step 6 specifies light forward pressure only with the shoe flat on the surface
Step 7: Finish and Release Trigger
When the cut is complete, release the trigger and wait for the blade to stop moving before lifting the saw away from the workpiece. On cordless jigsaws with electronic braking, the blade stops within one second of releasing the trigger. Never set the saw down while the blade is still moving.

Making an Internal Cutout

To cut a shape in the middle of a panel (a sink cutout, speaker opening, or access panel):

  1. Mark the outline clearly with a pencil.
  2. Drill a 1.5" starter hole inside the waste area, close to the cut line.
  3. Insert the jigsaw blade into the starter hole with the saw off.
  4. Plug in or insert the battery, pull the trigger to full speed, and begin cutting toward the nearest corner of your marked line.
  5. Follow the marked line around the full perimeter of the cutout.

Tips for Cleaner Cuts

  • Tape the cut line on plywood or laminate: Apply painter's tape over the cut area and mark the line on the tape. The tape's backing prevents tearout on the upstroke.
  • Cut finished side down: Most jigsaw blades cut on the upstroke, pulling toward the top face. Cutting with the finished side down protects the visible surface.
  • Use a fence or guide: For straight cuts, clamp a straight board as a guide fence. Rest the edge of the jigsaw shoe against it for a perfectly straight line.
  • Let the saw do the work: Pushing hard increases heat, bends the blade, and makes crooked cuts. Steady, light pressure gives the cleanest result.
  • Keep blades sharp: A dull blade causes burning, rough cuts, and excessive motor strain. Replace blades when they start dragging or chattering.
  • Score the cut line on hardwood: A sharp utility knife or marking knife run along the pencil line severs the surface fibers and dramatically reduces tearout on fine hardwood.
Proxxon Super-cut scroll saw blades for wood No. 9, 14 TPI -- the 14 TPI fine wood-cutting blades shown here suit the clean-cut techniques in the tips list above: a 14 TPI blade produces finer chips and less tearout on hardwood than a coarser blade; paired with the scoring technique in the last bullet, a fine-tooth blade severs wood fibers cleanly on both entry and exit strokes, minimizing chipping that coarser blades leave on finished hardwood surfaces

Frequently Asked Questions

What is a jigsaw tool used for?

A jigsaw cuts curves, shapes, and internal cutouts in wood, metal, laminate, tile, and plastic. It's the primary tool for cutting circles, arcs, templates, and custom shapes that would be impossible to make with a circular saw or table saw. It's also widely used for cutting outlet openings in cabinets, sink cutouts in countertops, and decorative woodworking profiles.

What does a jigsaw power tool do?

A jigsaw uses a short, narrow reciprocating blade to cut through materials. The blade moves up and down rapidly while the operator guides the saw along a drawn line. The narrow blade width lets it navigate curves and corners that a wider blade cannot follow. Variable speed and orbital action settings let the operator adjust cutting aggressiveness to match the material.

How do you use a jigsaw power tool for beginners?

Start by marking your cut line clearly on the workpiece, then clamp the material securely so it won't shift. Select the correct blade for your material, install it with the saw unplugged, and put on safety glasses and hearing protection. Rest the shoe on the edge of the material, start the blade at full speed before entering the cut, and guide it steadily along the outside of your pencil line using light forward pressure. When the cut is complete, release the trigger and wait for the blade to stop before lifting the saw.

Can a jigsaw cut straight lines?

Yes, but it requires a guide. Without a fence or straight edge clamped to the workpiece, it's easy to drift off a straight line with a jigsaw. For one-off straight cuts, clamp a straight board as a guide and run the jigsaw shoe against it. For repeated straight cuts, a circular saw or track saw is a better choice.

What's the difference between a jigsaw and a reciprocating saw?

A jigsaw has a short, narrow blade and is designed for controlled, precise cuts in materials up to 2" thick. Its narrow blade makes curves and shapes possible. A reciprocating saw has a longer, heavier blade designed for demolition, rough cutting, and getting into tight spaces — not precision work. A jigsaw is the fine tool; a reciprocating saw is the demolition tool.

Conclusion

Choose the right blade, follow the steps and use the tips for cleaner cuts, and a jigsaw will cut curves, straight lines and circles in wood, metal and plastic. Ready to compare models? Browse our full selection of jigsaws at Iron Line Tools.

Safety and standards references: OSHA woodworking eTool: handheld jig saws and OSHA 1910.243 guarding of portable powered tools.

Explore the category: Power Tools and Power Saws.

Shop Band Saws at Iron Line Tools

Maksiwa SF.35.MI 14 inch bandsaw with cast iron table and enclosed base

Maksiwa SF.35.MI 14" Bandsaw

Price: $2,399 | Type: Bandsaw

The Maksiwa SF.35.MI is a 14" professional woodworking bandsaw with cast iron table for stability and precision. Ideal for resawing, curves, and straight ripping in the woodshop.

Shop the Maksiwa SF.35.MI 14" Bandsaw →

Ellis 1600 Mitre Band Saw vertical cutting position with workpiece on table

Ellis 1600 Mitre Band Saw

Price: $5,299 | Type: Mitre Band Saw

The Ellis 1600 is a professional-grade horizontal/vertical mitre band saw with 10" round cutting capacity. Precision miter cuts from 0-60 degrees, heavy-duty USA-made construction.

Shop the Ellis 1600 Mitre Band Saw →

From blade choice to your first clean cut

Questions on setup, curves, circles or working in wood, metal and plastic? Our team is happy to help.

888-308-5580

Also browse: Band Saws

How-to guides, Power saws