RIKON 50-112 benchtop combination 4-inch by 36-inch belt and 6-inch disc sander showing how a sanding machine is set up and used

How to Use a Sander:
Setup, Grit, Technique & Safety

A sanding machine is only as good as the person using it. Get the abrasive wrong and the machine chews through material or clogs in minutes. Get the technique wrong and you score the surface. Here is everything you need to set up, run, and get clean results from a power sander.

Featured Sanding Machine

RIKON 50-114 combination 4 inch x 36 inch belt and 8 inch disc sander

RIKON

RIKON 50-114 4" x 36" Belt 8" Disc Sander

$279.99

Driven directly: a 4 inch by 36 inch belt and 8 inch disc share one direct drive power system on this RIKON, with a belt frame that moves from horizontal to vertical. Handy for learning belt and disc technique side by side.

View Product

RIKON 50-1305 combination 1 inch x 30 inch belt and 5 inch disc sander

RIKON

RIKON 50-1305 1" x 30" Belt / 5" Disc Sander

$149.99

Small bench sander with a 1 inch by 30 inch belt and a 5 inch disc, powered by a 1/3HP motor. Improved control systems and better dust removal efficiency suit the setup and dust steps in the guide.

View Product

Virutex ST62 Brush Sander For Curved Surfaces (120V) 6200599 professional brush sander with dust port designed for curved and irregular surfaces

Virutex

Virutex ST62 Brush Sander For Curved Surfaces (120V) 6200599

$380.00

Curves are the target of this Virutex ST62 brush sander, which has adjustable speed control and is used for satin finishing, polishing and surface preparation. A good model to learn once you know belt and orbital basics.

View Product

RIKON 50-1428 combination 1 inch x 42 inch belt and 8 inch disc sander

RIKON

RIKON 50-1428 1" x 42" Belt/ 8" Disc Sander

$399.99

Large handles make table angle adjustments easy on this RIKON, which pairs a 1 inch by 42 inch belt with an 8 inch disc on a cast iron base frame. A redesigned belt adjustment system helps with tracking and belt changes.

View Product

What Is a Sanding Machine Used For?

A sanding machine is used to abrade a surface — to remove material, level it, shape it, or refine its texture — faster and more consistently than hand sanding can achieve. The electric motor drives the abrasive continuously, so the machine cuts material every moment it is in contact with the workpiece rather than only on the push stroke the way a hand block does. That continuous cutting action is what makes a sanding machine worth using: what takes an hour by hand often takes a few minutes with the right power sander.

RIKON 50-112 combination belt and disc sander showing the belt station used for rapid material removal and surface conditioning

Practically, sanding machines are used across woodworking and metalworking for a wide range of tasks. In a woodworking shop, a sanding machine removes saw marks from lumber, flattens glued-up panels, cleans up tenon shoulders and edge joints, shapes curved parts, and prepares wood for finishing. In metalworking, the same class of machines deburrs machined parts, smooths weld seams, removes surface scale and rust, breaks sharp edges before assembly, and applies a consistent decorative finish to stainless steel or aluminum. The machine doesn't know or care about the material — what matters is matching the abrasive type and grit to the material and the task.

Safety Speed 3760 wide belt sander front view — industrial-grade surface conditioning machine used in metal fabrication shops for deburring sheet metal and applying consistent surface finishes

Beyond shaping and finishing, sanding machines also do surface preparation work: roughing a surface before bonding or painting so adhesives and coatings grip properly, removing old paint or finish to expose the substrate beneath, and conditioning a surface so the next process — welding, coating, gluing, or finishing — starts on a clean, consistent surface.

Sanders to Practice Belt, Orbital and Spindle Work

Use these models from our store alongside the guide's belt, random orbital and spindle steps. Check how each one handles dust before you buy, since the guide covers dust collection and safety.

1. Virutex Belt Sander LB31E: Powerful Sanding Performance 3100199 — $491.05

Practice belt sander technique on this model, which has a large working surface and a powerful motor for levelling and rough work. View more >

2. Proxxon Cordless Belt Sander BS/A — $300.60

Cordless belt sander with a 10.8V lithium-ion battery and continuously variable speed control. Handy for practicing speed control without dragging a cord around. View more >

3. RIKON 50-310 Benchtop Oscillating Spindle/Belt Sander — $349.99

Follow both the belt and spindle sections of the guide on one benchtop machine. Its 4 inch by 24 inch belt handles board edges and flat surfaces. View more >

4. Virutex LRE46L Orbital sander (120 V) 4600299 — $323.15

Dust collection system, electronic speed control and balanced construction make it a good model for the orbital and dust management parts of the guide. View more >

Choose the Right Sander Before You Start

No single sander does every job well. Choosing the wrong machine for the task creates more work, not less.

Belt sander — for rapid material removal, flattening, stripping, and heavy surface conditioning on flat or near-flat surfaces. See the full bench belt sanders collection for stationary options.

Random orbital sander — for general finishing and surface preparation on wood or painted surfaces. Versatile, portable, and leaves a swirl-free finish.

Sheet or orbital sander — for final finishing passes when the surface is already close and you want to refine it without removing much more material.

Spindle sander — for inside curves, curved edges, and contoured profiles. The bench sanders collection includes RIKON oscillating spindle models at $249.99 and $349.99.

Narrow precision belt sander — for tight profiles, mold work, and small precision parts. The Proxxon BS/E at $179.10 fits into the spaces a full-size bench machine cannot reach.

Proxxon BS/E narrow bench belt sander — the compact footprint and narrow 13/32-inch belt reach tight profiles and small part detail work that a standard bench machine cannot access

Sandpaper Grit: How to Read the Numbers

Sandpaper grit is a number that describes the coarseness of the abrasive. Lower numbers mean larger, more aggressive abrasive particles that remove material quickly and leave a rougher surface. Higher numbers mean finer particles that remove less material per pass and leave a smoother surface.

RIKON 50-320 oscillating spindle sander — grit selection on a spindle sander follows the same principle as any power sander: coarser grits for rapid shaping, finer grits for the finish pass on curved edges

60–80 grit (coarse): Aggressive stock removal, stripping paint or finish, removing rust, leveling uneven surfaces.

100–120 grit (medium-coarse): After coarse sanding, continues removing material while beginning to smooth out scratches left by the coarser belt.

150–180 grit (medium-fine): Surface refinement and final preparation for staining on most woods.

220 grit (fine): Final sanding before applying a finish on wood. Also used for light material removal on metal before coating.

320+ grit (extra fine): Sanding between coats of finish to knock down raised grain or dust nibs.

Work through grits in sequence and don't skip more than one step at a time. For metal, see the guide on using a belt sander on metal for abrasive selection.

How to Use a Belt Sander

Set up the machine first. On a stationary bench belt/disc sander, adjust the belt tracking so the belt runs centered on the platen and doesn't walk off the edge of the drums. Most machines have a tracking knob — with the machine running, adjust it until the belt runs steady and true. Check that the work table is set to the correct angle.

Install the right belt. Match the abrasive type and grit to the material and task. For wood sanding, aluminum oxide belts are the standard starting point. Thread the belt through the machine with the arrow on the back of the belt pointing in the direction of travel.

Move the workpiece, not just one spot. Keep the workpiece moving with a steady, even pass — bring it into contact with the belt, move it across the platen from one side to the other in a smooth stroke, and lift it away. Holding the workpiece still concentrates the cut and creates a hollow in the surface.

RIKON 50-112 belt and disc sander showing the adjustable work table — the table supports the workpiece for steady, even strokes across the belt and holds it at the correct angle for edge and end-grain work

Use moderate, even pressure. Let the abrasive do the work. Excessive pressure generates heat, loads the belt faster, and often produces a rougher finish.

Check the surface and belt condition regularly. A loaded or worn belt slides across the surface rather than cutting it. Replace the belt rather than pressing harder through a worn abrasive.

Close-up of Proxxon BS/E sanding belt and drive wheel — a worn or loaded belt slides over the surface rather than cutting it; replace the belt as soon as the cut slows or the surface starts to burnish

How to Use a Random Orbital Sander

Choose and attach the correct disc. Random orbital sanders use hook-and-loop discs that press onto the pad. Align the holes in the disc with the holes in the pad — these holes connect to the machine's dust collection port.

Virutex LRE46L orbital sander in use on a wooden surface — properly aligned disc holes connect the pad to the dust port so particles are captured rather than spread across the workpiece surface

Start the sander before touching the workpiece. Bring the spinning sander into contact with the surface rather than starting it while it sits on the surface.

Hold the sander flat and apply even pressure. The pad must stay flat against the surface. Tilting the sander creates swirl marks and an uneven cut.

Move in any direction — but keep moving. Unlike belt and sheet sanders, a random orbital leaves no consistent scratch pattern and can be moved in any direction. Keep the machine moving to prevent over-sanding any single area.

Work through grits in sequence. After each grit change, check under raking light to confirm the scratches from the previous grit are gone before moving to the next step.

Close-up of Virutex LRE46L orbital sander pad and disc attachment — checking under raking light after each grit change confirms whether the previous grit scratch pattern is fully eliminated before moving on

How to Use a Spindle Sander

Select the correct spindle diameter. Choose the spindle whose diameter closely matches the radius of the curve you are sanding. A spindle much smaller than the curve leaves a flat spot; a spindle larger than the curve doesn't fit into the material.

Install the sanding sleeve and rubber drum. Slide the sleeve over the drum with the machine off, making sure it seats fully and evenly. A sleeve that hangs low on one side will sand unevenly and wear faster on one edge.

Move the workpiece steadily against the spindle. Hold the workpiece flat on the table and feed it into the spindle with light, even pressure. Follow the curve in a smooth motion and keep it moving to prevent the spindle from digging a groove into the surface.

Use the table angle for bevel sanding. Most spindle sander tables tilt to set a precise bevel angle for compound-curved bevels.

RIKON 50-320 oscillating spindle sander table and spindle showing how the workpiece rests flat on the table and feeds into the spindle — the table tilts to set bevel angles for angled inside-curve work

Safety and Dust Collection

Always wear safety glasses. Both wood dust and metal particles travel at speed from a running sander.

Wear a dust mask or respirator for extended sanding sessions. Fine wood dust is a known respiratory irritant, and metal dust is denser and more hazardous. A basic N95 is the minimum; a half-face respirator with P100 filters provides substantially better protection for production sanding.

Connect to a dust collection system where possible. Most stationary bench sanders have a dust port that accepts a standard shop vacuum hose. Empty the collection bag or canister before it reaches capacity.

Secure the workpiece before starting. Small parts that aren't firmly supported can be grabbed by the belt or disc and thrown. Use the work table to support the workpiece.

Keep ferrous and non-ferrous sanding separate. Steel particles embedded in a belt from a previous ferrous job will contaminate an aluminum surface on the next use.

Operator feeding material through the Safety Speed 3760 wide belt sander — in production metal fabrication, dedicated machines or clearly labeled belt sets prevent cross-contamination between ferrous and non-ferrous materials
Model Type Best For Price
Proxxon BS/E Precision bench belt sander Small parts, profiles, detail finishing $179.10
RIKON 50-112 Belt + disc combo sander General benchtop sanding, edge work, end grain $179.99
RIKON 50-320 Oscillating spindle sander Inside curves and contoured edges $249.99
RIKON 50-114 Belt + 8" disc combo sander Woodworking, metalworking, larger disc station $279.99
RIKON 50-310 Spindle + belt combo sander Curved and straight work, one machine $349.99
RIKON 50-310 oscillating spindle and belt sander combination — pairs the spindle station for curved inside-edge work with a belt station for straight edges and flat sanding in a single compact benchtop footprint

Frequently Asked Questions

Do you sand with or against the grain?

Belt and sheet sanders should generally be used parallel to the wood grain — sanding across the grain leaves scratches that run perpendicular to the surface fibers and are difficult to remove at finer grits. Random orbital sanders can be moved in any direction because their random path leaves no consistent scratch pattern.

How do I know when to change sandpaper grit?

Move to the next finer grit when the scratch pattern from the current grit is consistent across the whole surface — when the deeper scratches from the previous grit are gone. Check by shining a light at a low, raking angle across the surface. Deep scratches appear as shadows; when the surface looks uniformly textured under raking light, that grit is done.

Why is my belt sander leaving swirl marks?

Swirl marks on wood from a belt sander usually mean the belt is loaded with sawdust, worn, or the machine is being held stationary rather than moving across the surface. A loaded belt glazes the surface rather than cutting it. Replace the belt and keep the workpiece moving in a consistent stroke.

What grit sandpaper should I use to remove paint?

Start at 60 or 80 grit for paint removal on a flat surface with a belt sander or random orbital. Coarse grit cuts through the paint film quickly without loading as fast as finer grits. Once the paint is off and you are working the bare substrate, progress through finer grits to prepare the surface for a new coat.

Can I use the same sander for wood and metal?

Yes — the same machine handles both with a belt change. Swap the wood belt for a metal-appropriate abrasive (zirconia or ceramic for ferrous metals, open-coat aluminum oxide for aluminum) and you are ready for metal work. Keep separate belt or disc sets for wood and metal to prevent cross-contamination.

Conclusion

Get the abrasive, the setup and the technique right, and manage dust, and your sanding machine will leave a clean, even surface. To see current models and pricing, explore our sanding machines collection.

Safety and standards references: OSHA woodworking eTool: sanders and OSHA woodworking eTool: wood dust.

Is your grit right for the sander you use?

Bring your belt, random orbital or spindle questions to our team and we will help you plan setup and dust collection.

888-308-5580

How-to guides, Sanders